|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER FEATURES * 5 differential 3.3V LVPECL outputs * Selectable differential clock inputs * CLKx, nCLKx pair can accept the following differential input levels: LVPECL, LVDS, LVHSTL, HCSL, SSTL * Output frequency range: 31.25MHz to 700MHz * Input frequency range: 31.25MHz to 700MHz * VCO range: 250MHz to 700MHz * External feedback for "zero delay" clock regeneration * Cycle-to-cycle jitter: 25ps (maximum) * Output skew: 25ps (maximum) * PLL reference zero delay: 50ps 100ps * 3.3V operating supply * 0C to 70C ambient operating temperature * Lead-Free package available * Industrial temperature information available upon request GENERAL DESCRIPTION The ICS8634-01 is a high performance 1-to-5 Differential-to-3.3V LVPECL Zero Delay Buffer and a HiPerClockSTM member of the HiPerClockSTM family of High Performance Clock Solutions from ICS. The ICS863401 has two selectable clock inputs. The CLKx, nCLKx pair can accept most standard differential input levels. Utilizing one of the outputs as feedback to the PLL, output frequencies up to 700MHz can be regenerated with zero delay with respect to the input. Dual reference clock inputs support redundant clock or multiple reference applications. ICS BLOCK DIAGRAM Q0 nQ0 PLL_SEL PIN ASSIGNMENT PLL_SEL VCCO VCCA nQ4 VCC VEE VEE Q4 CLK0 nCLK0 CLK1 nCLK1 CLK_SEL FB_IN nFB_IN /4, /8 0 Q1 nQ1 0 Q2 nQ2 1 Q3 nQ3 SEL0 SEL1 CLK0 nCLK0 CLK1 nCLK1 CLK_SEL MR 1 2 3 4 5 6 7 8 32 31 30 29 28 27 26 25 24 23 22 VCCO Q3 nQ3 Q2 nQ2 Q1 nQ1 VCCO 1 PLL Q4 nQ4 ICS8634-01 21 20 19 18 17 9 10 11 12 13 14 15 16 VCC nFB_IN FB_IN VEE VEE nQ0 Q0 VCCO SEL0 SEL1 MR 32-Lead LQFP 7mm x 7mm x 1.4mm package body Y Package Top View 32-Lead VFQFN 5mm x 5mm x 0.95 package body K Package Top View 8634BY-01 www.icst.com/products/hiperclocks.html 1 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER Type Description TABLE 1. PIN DESCRIPTIONS Number 1 2 3 4 5 6 7 Name SEL0 SEL1 CLK0 nCLK0 CLK1 nCLK1 CLK_SEL Input Input Input Input Input Input Input Pulldown Determines output divider values in Table 3. LVCMOS / LVTTL interface levels. Pulldown Determines output divider values in Table 3. LVCMOS / LVTTL interface levels. Pulldown Non-inver ting differential clock input. Pullup Pullup Inver ting differential clock input. Pulldown Non-inver ting differential clock input. Inver ting differential clock input. Clock select input. When LOW, selects CLK0, nCLK0. Pulldown When HIGH, selects CLK1, nCLK1. LVCMOS / LVTTL interface levels. Active High Master Reset. When logic HIGH, the internal dividers are reset causing the true outputs Qx to go low and the inver ted outputs nQx to go Pulldown high. When logic LOW, the internal dividers and the outputs are enabled. LVCMOS / LVTTL interface levels. Core supply pins. Pullup Feedback input to phase detector for regenerating clocks with "zero delay". Pulldown Feedback input to phase detector for regenerating clocks with "zero delay". Negative supply pins. Differential output pair. LVPECL interface levels. Output supply pins. Differential output pair. LVPECL interface levels. Differential output pair. LVPECL interface levels. Differential output pair. LVPECL interface levels.. Differential output pair. LVPECL interface levels. Analog supply pin. Selects between the PLL and the reference clock as the input to the dividers. When HIGH, selects PLL. When LOW, selects reference clock. LVCMOS / LVTTL interface levels. 8 9, 32 10 11 12, 13 28, 29 14, 15 16. 17, 24, 25 18, 19 20, 21 22, 23 26, 27 30 31 MR VCC nFB_IN FB_IN V EE nQ0, Q0 VCCO nQ1, Q1 nQ2, Q2 nQ3, Q3 nQ4, Q4 VCCA PLL_SEL Input Power Input Input Power Output Power Output Output Output Output Power Input Pullup NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values. TABLE 2. PIN CHARACTERISTICS Symbol CIN RPULLUP RPULLDOWN Parameter Input Capacitance Input Pullup Resistor Input Pulldown Resistor Test Conditions Minimum Typical 4 51 51 Maximum Units pF K K TABLE 3A. CONTROL INPUT FUNCTION TABLE Inputs SEL1 SEL0 0 0 1 0 1 0 Reference Frequency Range (MHz)* 250 - 700 125 - 350 62.5 - 175 Outputs PLL_SEL = 1 PLL Enable Mode Q0:Q4, nQ0:nQ4 /1 /1 /1 /1 TABLE 3B. PLL BYPASS FUNCTION TABLE Inputs SEL1 SEL0 0 0 1 1 0 1 0 1 Outputs PLL_SEL = 0 PLL Bypass Mode Q0:Q4, nQ0:nQ4 /4 /4 /4 /8 1 1 31.25 - 87.5 *NOTE: VCO frequency range for all configurations above is 250MHz to 700MHz. 8634BY-01 www.icst.com/products/hiperclocks.html 2 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER 4.6V -0.5V to VCC + 0.5V 50mA 100mA 47.9C/W (0 lfpm) 34.8C/W (0 lfpm) -65C to 150C NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Character- ABSOLUTE MAXIMUM RATINGS Supply Voltage, VCC Inputs, VI Outputs, IO Continuous Current Surge Current Package Thermal Impedance, JA 32 Lead LQFP 32 Lead VFQFN Storage Temperature, TSTG istics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C Symbol VCC VCCA VCCO I EE ICCA Parameter Core Supply Voltage Analog Supply Voltage Output Supply Voltage Power Supply Current Analog Supply Current Test Conditions Minimum 3.135 3.135 3.135 Typical 3.3 3.3 3.3 Maximum 3.465 3.465 3.465 150 15 Units V V V mA mA TABLE 4B. LVCMOS/LVTTL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C Symbol Parameter VIH VIL IIH Input High Voltage Input Low Voltage Input High Current SEL0, SEL1, CLK_SEL, MR PLL_SEL IIL Input Low Current SEL0, SEL1, CLK_SEL, MR PLL_SEL VCC = VIN = 3.465V VCC = VIN = 3.465V VCC = 3.465V, VIN = 0V VCC = 3.465V, VIN = 0V -5 -150 Test Conditions Minimum 2 -0.3 Typical Maximum VCC + 0.3 0.8 150 5 Units V V A A A A TABLE 4C. DIFFERENTIAL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C Symbol IIH IIL VPP Parameter Input High Current Input Low Current CLK0, CLK1, FB_IN nCLK0, nCLK1, nFB_IN CLK0, CLK1, FB_IN nCLK0, nCLK1, nFB_IN Test Conditions VCC = VIN = 3.465V VCC = VIN = 3.465V VCC = 3.465V, VIN = 0V VCC = 3.465V, VIN = 0V -5 -150 0.15 1.3 Minimum Typical Maximum 150 5 Units A A A A V V Peak-to-Peak Input Voltage VCMR Common Mode Input Voltage; NOTE 1, 2 VEE + 0.5 VCC - 0.85 NOTE 1: For single ended applications, the maximum input voltage for CLK0, nCLK0 and CLK1, nCLK1 is VCC + 0.3V. NOTE 2: Common mode voltage is defined as VIH. 8634BY-01 www.icst.com/products/hiperclocks.html 3 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER Test Conditions Minimum VCCO - 1.4 VCCO - 2.0 0.6 Typical Maximum VCCO - 1.0 VCCO - 1.7 1.0 Units V V V TABLE 4D. LVPECL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C Symbol VOH VOL VSWING Parameter Output High Voltage; NOTE 1 Output Low Voltage; NOTE 1 Peak-to-Peak Output Voltage Swing NOTE 1: Outputs terminated with 50 to VCCO - 2V. TABLE 5. INPUT FREQUENCY CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C Symbol fIN Parameter Input Frequency CLK0, nCLK0, CLK1, nCLK1 Test Conditions PLL_SEL = 1 PLL_SEL = 0 Minimum 31.25 Typical Maximum 700 700 Units MHz MHz TABLE 6. AC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V5%, TA = 0C TO 70C Symbol fMAX tPD Parameter Output Frequency Propagation Delay; NOTE 1 PLL Reference Zero Delay; NOTE 2, 4 Output Skew; NOTE 3, 4 Cycle-to-Cycle Jitter ; NOTE 4, 6 Phase Jitter ; NOTE 4, 5, 6 PLL Lock Time Output Rise/Fall Time 20% to 80% @ 50MHz 300 PLL_SEL = 0V, f 700MHz PLL_SEL = 3.3V 3.2 -50 50 Test Conditions Minimum Typical Maximum 700 4.2 150 25 25 50 1 700 Units MHz ns ps ps ps ps ms ps % t(O) t sk(o) t jit(cc) t jit() tL tR / tF odc Output Duty Cycle 47 53 All parameters measured at fMAX unless noted otherwise. NOTE 1: Measured from the differential input crossing point to the differential output crossing point. NOTE 2: Defined as the time difference between the input reference clock and the average feedback input signal when the PLL is locked and the input reference frequency is stable. NOTE 3: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at the output differential cross points. NOTE 4: This parameter is defined in accordance with JEDEC Standard 65. NOTE 5: Phase jitter is dependent on the input source used. NOTE 6: Characterized at VCO frequency of 622MHz. 8634BY-01 www.icst.com/products/hiperclocks.html 4 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER PARAMETER MEASUREMENT INFORMATION 2V VCC, VCCA, VCCO Qx SCOPE V CC LVPECL VEE nQx nCLK0, nCLK1 V CLK0, CLK1 VEE PP Cross Points V CMR -1.3V 0.165V 3.3V OUTPUT LOAD AC TEST CIRCUIT DIFFERENTIAL INPUT LEVEL nQ0:nQ4 nQx Qx Q0:Q4 tcycle n nQy Qy tsk(o) tjit(cc) = tcycle n -tcycle n+1 1000 Cycles OUTPUT SKEW 80% VSW I N G Clock Outputs 20% tR tF 20% CYCLE-TO-CYCLE JITTER nQ0:nQ4 80% Q0:Q4 Pulse Width t PERIOD odc = t PW t PERIOD OUTPUT RISE/FALL TIME OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD nCLK0, nCLK1 VOH VOL VOH VOL nCLK0, nCLK1 CLK0, CLK1 nQ0:nQ4 Q0:Q4 tPD CLK0, CLK1 nFB_IN FB_IN t(O) tjit(O) = t(O) -- t(O) mean = Phase Jitter t(O) mean = Static Phase Offset (where t(O) is any random sample, and t(O) mean is the average of the sampled cycles measured on controlled edges) PROPAGATION DELAY 8634BY-01 PHASE JITTER & STATIC PHASE OFFSET www.icst.com/products/hiperclocks.html 5 REV. C NOVEMBER 12, 2004 tcycle n+1 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER APPLICATION INFORMATION WIRING THE DIFFERENTIAL INPUT TO ACCEPT SINGLE ENDED LEVELS Figure 1 shows how the differential input can be wired to accept single ended levels. The reference voltage V_REF ~ VCC/2 is generated by the bias resistors R1, R2 and C1. This bias circuit should be located as close as possible to the input pin. The ratio of R1 and R2 might need to be adjusted to position the V_REF in the center of the input voltage swing. For example, if the input clock swing is only 2.5V and VCC = 3.3V, V_REF should be 1.25V and R2/R1 = 0.609. VCC R1 1K Single Ended Clock Input CLKx V_REF nCLKx C1 0.1u R2 1K FIGURE 1. SINGLE ENDED SIGNAL DRIVING DIFFERENTIAL INPUT TERMINATION FOR LVPECL OUTPUTS The clock layout topology shown below is a typical termination for LVPECL outputs. The two different layouts mentioned are recommended only as guidelines. FOUT and nFOUT are low impedance follower outputs that generate ECL/LVPECL compatible outputs. Therefore, terminating resistors (DC current path to ground) or current sources must be used for functionality. These outputs are designed to drive 50 transmission lines. Matched impedance techniques should be used to maximize operating frequency and minimize signal distortion. Figures 2A and 2B show two different layouts which are recommended only as guidelines. Other suitable clock layouts may exist and it would be recommended that the board designers simulate to guarantee compatibility across all printed circuit and clock component process variations. 3.3V Zo = 50 125 125 FOUT FIN Zo = 50 FOUT FIN Zo = 50 50 1 RTT = Z ((VOH + VOL) / (VCC - 2)) - 2 o 50 VCC - 2V RTT Zo = 50 84 84 FIGURE 2A. LVPECL OUTPUT TERMINATION 8634BY-01 FIGURE 2B. LVPECL OUTPUT TERMINATION REV. C NOVEMBER 12, 2004 www.icst.com/products/hiperclocks.html 6 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER POWER SUPPLY FILTERING TECHNIQUES As in any high speed analog circuitry, the power supply pins are vulnerable to random noise. The ICS8634-01 provides separate power supplies to isolate any high switching noise from the outputs to the internal PLL. VCC, VCCA, and VCCO should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter performance, power supply isolation is required. Figure 3 illustrates how a 10 resistor along with a 10F and a .01F bypass capacitor should be connected to each VCCA pin. 3.3V VCC .01F VCCA .01F 10 F 10 FIGURE 3. POWER SUPPLY FILTERING DIFFERENTIAL CLOCK INPUT INTERFACE The CLK /nCLK accepts LVDS, LVPECL, LVHSTL, SSTL, HCSL and other differential signals. Both VSWING and VOH must meet the VPP and VCMR input requirements. Figures 4A to 4D show interface examples for the HiPerClockS CLK/nCLK input driven by the most common driver types. The input interfaces suggested here are examples only. Please consult with the vendor of the driver component to confirm the driver termination requirements. For example in Figure 4A, the input termination applies for ICS HiPerClockS LVHSTL drivers. If you are using an LVHSTL driver from another vendor, use their termination recommendation. 3.3V 3.3V 3.3V 1.8V Zo = 50 Ohm Zo = 50 Ohm CLK Zo = 50 Ohm nCLK LVHSTL ICS HiPerClockS LVHSTL Driver R1 50 R2 50 R3 50 LVPECL Zo = 50 Ohm CLK nCLK HiPerClockS Input HiPerClockS Input R1 50 R2 50 FIGURE 4A. HIPERCLOCKS CLK/nCLK INPUT DRIVEN ICS HIPERCLOCKS LVHSTL DRIVER BY FIGURE 4B. HIPERCLOCKS CLK/nCLK INPUT DRIVEN 3.3V LVPECL DRIVER BY 3.3V 3.3V 3.3V R3 125 Zo = 50 Ohm CLK Zo = 50 Ohm nCLK LVPECL R1 84 R2 84 HiPerClockS Input R4 125 3.3V 3.3V LVDS_Driv er Zo = 50 Ohm CLK R1 100 nCLK Receiv er Zo = 50 Ohm FIGURE 4C. HIPERCLOCKS CLK/nCLK INPUT DRIVEN 3.3V LVPECL DRIVER 8634BY-01 BY FIGURE 4D. HIPERCLOCKS CLK/nCLK INPUT DRIVEN 3.3V LVDS DRIVER BY www.icst.com/products/hiperclocks.html 7 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER depend on the selected component types, the density of the components, the density of the traces, and the stack up of the P.C. board. LAYOUT GUIDELINE The schematic of the ICS8634-01 layout example is shown in Figure 5A. The ICS8634-01 recommended PCB board layout for this example is shown in Figure 5B. This layout example is used as a general guideline. The layout in the actual system will VCC SP = Space (i.e. not intstalled) VCCA RU2 SP RU3 1K RU4 1K RU5 SP R7 10 VCC VCC=3.3V CLK_SEL PLL_SEL SEL0 SEL1 C11 0.01u VCCO=3.3V DIV_SEL[1:0] = 01 PLL_SEL C16 10u 155.5 MHz Zo = 50 Ohm + RD2 1K RD3 SP RD4 SP RD5 1K VCC VCCO Zo = 50 Ohm LVPECL_input U1 3.3V R5 50 R4 50 (155.5 MHz) Zo = 50 Ohm VCC PLL_SEL VCCA VEE VEE Q4 nQ4 VCCO 32 31 30 29 28 27 26 25 SEL0 SEL1 Zo = 50 Ohm CLK_SEL 3.3V PECL Driver R8 50 R9 50 1 2 3 4 5 6 7 8 VCC nFB_IN FB_IN VEE VEE nQ0 Q0 VCCO SEL0 SEL1 CLK0 nCLK0 CLK1 nCLK2 CLK_SEL MR VCCO Q3 nQ3 Q2 nQ2 Q1 nQ1 VCCO 24 23 22 21 20 19 18 17 R6 50 Output Termination Example Bypass capacitor located near the power pins (U1-9) VCC C1 0.1uF (U1-32) C6 0.1uF R10 50 9 10 11 12 13 14 15 16 8634-01 (U1-16) R2 50 R1 50 C2 0.1uF R3 50 VCCO (U1-17) C4 0.1uF (U1-24) C5 0.1uF (U1-25) C7 0.1uF FIGURE 5A. ICS8634-01 LVPECL ZERO DELAY BUFFER SCHEMATIC EXAMPLE 8634BY-01 www.icst.com/products/hiperclocks.html 8 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. The following component footprints are used in this layout example: All the resistors and capacitors are size 0603. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER trace delay might be restricted by the available space on the board and the component location. While routing the traces, the clock signal traces should be routed first and should be locked prior to routing other signal traces. * The differential 50 output traces should have same length. * Avoid sharp angles on the clock trace. Sharp angle turns cause the characteristic impedance to change on the transmission lines. * Keep the clock traces on the same layer. Whenever possible, avoid placing vias on the clock traces. Placement of vias on the traces can affect the trace characteristic impedance and hence degrade signal integrity. * To prevent cross talk, avoid routing other signal traces in parallel with the clock traces. If running parallel traces is unavoidable, allow a separation of at least three trace widths between the differential clock trace and the other signal trace. * Make sure no other signal traces are routed between the clock trace pair. * The matching termination resistors should be located as close to the receiver input pins as possible. POWER AND GROUNDING Place the decoupling capacitors C1, C2, C4, C5, C6, and C7, as close as possible to the power pins. If space allows, placement of the decoupling capacitor on the component side is preferred. This can reduce unwanted inductance between the decoupling capacitor and the power pin caused by the via. Maximize the power and ground pad sizes and number of vias capacitors. This can reduce the inductance between the power and ground planes and the component power and ground pins. The RC filter consisting of R7, C11, and C16 should be placed as close to the VCCA pin as possible. CLOCK TRACES AND TERMINATION Poor signal integrity can degrade the system performance or cause system failure. In synchronous high-speed digital systems, the clock signal is less tolerant to poor signal integrity than other signals. Any ringing on the rising or falling edge or excessive ring back can cause system failure. The shape of the trace and the GND R7 C16 C11 C7 C6 C5 VCCO VCC U1 Pin 1 VCCA VIA 50 Ohm Traces C4 C1 C2 FIGURE 5B. PCB BOARD LAYOUT FOR ICS8634-01 8634BY-01 www.icst.com/products/hiperclocks.html 9 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER POWER CONSIDERATIONS This section provides information on power dissipation and junction temperature for the ICS8634-01. Equations and example calculations are also provided. 1. Power Dissipation. The total power dissipation for the ICS8634-01 is the sum of the core power plus the power dissipated in the load(s). The following is the power dissipation for VCC = 3.3V + 5% = 3.465V, which gives worst case results. NOTE: Please refer to Section 3 for details on calculating power dissipated in the load. * * Power (core)MAX = VCC_MAX * IEE_MAX = 3.465V * 150mA = 520mW Power (outputs)MAX = 30.2mW/Loaded Output pair If all outputs are loaded, the total power is 5 * 30.2mW = 151mW Total Power_MAX (3.465V, with all outputs switching) = 520mW + 151mW = 671mW 2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the device. The maximum recommended junction temperature for HiPerClockSTM devices is 125C. The equation for Tj is as follows: Tj = JA * Pd_total + TA Tj = Junction Temperature JA = Junction-to-Ambient Thermal Resistance Pd_total = Total Device Power Dissipation (example calculation is in section 1 above) TA = Ambient Temperature In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance JA must be used. Assuming a moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 42.1C/W per Table 7A below. Therefore, Tj for an ambient temperature of 70C with all outputs switching is: 70C + 0.671W * 42.1C/W = 98.2C. This is well below the limit of 125C. This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow, and the type of board (single layer or multi-layer). TABLE 7A. THERMAL RESISTANCE JA FOR 32-PIN LQFP, FORCED CONVECTION JA by Velocity (Linear Feet per Minute) 0 200 500 Single-Layer PCB, JEDEC Standard Test Boards 67.8C/W 55.9C/W 50.1C/W Multi-Layer PCB, JEDEC Standard Test Boards 47.9C/W 42.1C/W 39.4C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TABLE 7B. JAVS. AIR FLOW TABLE FOR 32 LEAD VFQFN PACKAGE JA 0 Air Flow (Linear Feet per Minute) 0 Multi-Layer PCB, JEDEC Standard Test Boards 34.8C/W 8634BY-01 www.icst.com/products/hiperclocks.html 10 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. 3. Calculations and Equations. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER The purpose of this section is to derive the power dissipated into the load. LVPECL output driver circuit and termination are shown in Figure 6. VCCO Q1 VOUT RL 50 VCCO - 2V FIGURE 6. LVPECL DRIVER CIRCUIT AND TERMINATION To calculate worst case power dissipation into the load, use the following equations which assume a 50 load, and a termination voltage of V - 2V. CCO * For logic high, VOUT = V (V CCO_MAX OH_MAX =V CCO_MAX - 1.0V -V OH_MAX ) = 1.0V =V - 1.7V * For logic low, VOUT = V (V CCO_MAX OL_MAX CCO_MAX -V OL_MAX ) = 1.7V Pd_H is power dissipation when the output drives high. Pd_L is the power dissipation when the output drives low. Pd_H = [(V - (V - 2V))/R ] * (V L OH_MAX CCO_MAX CCO_MAX -V OH_MAX ) = [(2V - (V CCO_MAX -V OH_MAX ))/R ] * (V L CCO_MAX -V OH_MAX )= [(2V - 1V)/50] * 1V = 20.0mW ))/R ] * (V L Pd_L = [(V OL_MAX - (V CCO_MAX - 2V))/R ] * (V L CCO_MAX -V OL_MAX ) = [(2V - (V CCO_MAX -V OL_MAX CCO_MAX -V OL_MAX )= [(2V - 1.7V)/50] * 1.7V = 10.2mW Total Power Dissipation per output pair = Pd_H + Pd_L = 30.2mW 8634BY-01 www.icst.com/products/hiperclocks.html 11 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER RELIABILITY INFORMATION TABLE 8A. JAVS. AIR FLOW TABLE FOR 32 LQFP JA by Velocity (Linear Feet per Minute) 0 Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 67.8C/W 47.9C/W 200 55.9C/W 42.1C/W 500 50.1C/W 39.4C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TABLE 8B. JAVS. AIR FLOW TABLE FOR 32 LEAD VFQFN PACKAGE JA 0 Air Flow (Linear Feet per Minute) 0 Multi-Layer PCB, JEDEC Standard Test Boards 34.8C/W TRANSISTOR COUNT The transistor count for ICS8634-01 is: 2969 8634BY-01 www.icst.com/products/hiperclocks.html 12 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER 32 LEAD LQFP PACKAGE OUTLINE - Y SUFFIX FOR TABLE 9. PACKAGE DIMENISIONS JEDEC VARIATION ALL DIMENSIONS IN MILLIMETERS BBA SYMBOL N A A1 A2 b c D D1 D2 E E1 E2 e L ccc 0.45 0 0.05 1.35 0.30 0.09 9.00 BASIC 7.00 BASIC 5.60 9.00 BASIC 7.00 BASIC 5.60 0.80 BASIC 0.60 0.75 7 0.10 1.40 0.37 MINIMUM NOMINAL 32 1.60 0.15 1.45 0.45 0.20 MAXIMUM Reference Document: JEDEC Publication 95, MS-026 8634BY-01 www.icst.com/products/hiperclocks.html 13 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER 32 LEAD VFQFN PACKAGE OUTLINE - K SUFFIX FOR TABLE 9B. PACKAGE DIMENSIONS JEDEC VARIATION ALL DIMENSIONS IN MILLIMETERS SYMBOL N A A1 A3 b e ND NE D D2 E E2 L 1.25 0.30 1.25 5.0 3.25 0.50 0.18 0.50 BASIC 8 8 5.0 3.25 0.80 0 0.25 Reference 0.30 MINIMUM 32 1.0 0.05 MAXIMUM Reference Document: JEDEC Publication 95, MO-220 8634BY-01 www.icst.com/products/hiperclocks.html 14 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER Marking ICS8634BY-01 ICS8634BY-01 ICS8634BY01L ICS8634BY01L ICS8634BK01 ICS8634BK01 Package 32 Lead LQFP 32 Lead LQFP on Tape and Reel 32 Lead "Lead-Free" LQFP 32 Lead "Lead-Free" LQFP on Tape and Reel 32 Lead VFQFN 32 Lead VFQFN on Tape and Reel Count 250 per Tray 1000 250 per Tray 1000 490 per Tray 2500 Temperature 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C TABLE 10. ORDERING INFORMATION Part/Order Number ICS8634BY-01 ICS8634BY-01T ICS8634BY-01LF ICS8634BY-01LFT ICS8634BK-01 ICS8634BK-01T The aforementioned trademark, HiPerClockSTM is a trademark of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 8634BY-01 www.icst.com/products/hiperclocks.html 15 REV. C NOVEMBER 12, 2004 Integrated Circuit Systems, Inc. ICS8634-01 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL ZERO DELAY BUFFER REVISION HISTORY SHEET Description of Change Updated Block Diagram. Added note at bottom of the table. Added Note 6. Added Termination for LVPECL Outputs and Power Supply Filtering Techniques sections. Pin Description table - revised MR description. 3.3V Output Load Test Circuit Diagram - revised VEE equation from 0.135 to 0.165. Updated Output Rise/Fall Time Diagram. Power Considerations/Calculations & Equations - updated power dissipation equations. Revised MR and VCC pin descriptions. VCC Parameter replaced Positive Supply Voltage with Core Supply Voltage. Changed VSWING (max) limit from 900mV to 1.0V. Updated Fig. 1, Single Ended Signal Driving Differential Input and LVPECL Output Termination Diagrams. Updated format. Pin Characteristics Table - changed CIN 4pF max. to 4pF typical. Absolute Maximum Ratings - updated Outputs. AC Characteristics Table - modified tPD limit from 3.6ns min. to 3.2ns min. and deleted 3.9ns typical. Updated LVPECL Output Termination drawings. Added Differential Clock Input Interface section. Ordering Information Table - added Lead-Free par t number. Add 32 Lead VFQFN package throughout data sheet. Date 11/2/01 11/20/01 6/3/02 Rev A A A Table T3A T6 Page 1 3 5 9 2 6 A T1 8 14 T1 T4A T4D 2 3 4 6 8/22/02 B 3/5/03 T2 T6 C 2 3 4 6 7 14 8/26/04 C C T10 10/15/04 11/12/04 8634BY-01 www.icst.com/products/hiperclocks.html 16 REV. C NOVEMBER 12, 2004 |
Price & Availability of ICS8634-01 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |